Here is a copy of the diagram shown earlier that illustrates a Texinfo file with three chapters, each of which contains two sections.
The “root” is at the top of the diagram and the “leaves” are at the bottom. This is how such a diagram is drawn conventionally; it illustrates an upside-down tree. For this reason, the root node is called the ‘Top’ node, and ‘Up’ node pointers carry you closer to the root.
Top | ------------------------------------- | | | Chapter 1 Chapter 2 Chapter 3 | | | -------- -------- -------- | | | | | | Section Section Section Section Section Section 1.1 1.2 2.1 2.2 3.1 3.2
Using explicit pointers (not recommended, but for shown for purposes of the example), the fully-written command to start Chapter 2 would be this:
@node Chapter 2, Chapter 3, Chapter 1, Top @comment node-name, next, previous, up
This @node
line says that the name of this node is
“Chapter 2”, the name of the ‘Next’ node is “Chapter 3”, the
name of the ‘Previous’ node is “Chapter 1”, and the name of the
‘Up’ node is “Top”. You can (and should) omit writing out these
node names if your document is hierarchically organized
(see makeinfo Pointer Creation), but the pointer
relationships still obtain.
Note: ‘Next’ and ‘Previous’ refer to nodes at the same hierarchical level in the manual, not necessarily to the next node within the Texinfo file. In the Texinfo file, the subsequent node may be at a lower level—a section-level node most often follows a chapter-level node, for example. (The ‘Top’ node contains the exception to this rule. Since the ‘Top’ node is the only node at that level, ‘Next’ refers to the first following node, which is almost always a chapter or chapter-level node.)
To go to Sections 2.1 and 2.2 using Info, you need a menu inside Chapter 2. (See Menus.) You would write the menu just before the beginning of Section 2.1, like this:
@menu * Sect. 2.1:: Description of this section. * Sect. 2.2:: Description. @end menu
Using explicit pointers, the node for Sect. 2.1 is written like this:
@node Sect. 2.1, Sect. 2.2, Chapter 2, Chapter 2 @comment node-name, next, previous, up
In Info format, the ‘Next’ and ‘Previous’ pointers of a node usually lead to other nodes at the same level—from chapter to chapter or from section to section (sometimes, as shown, the ‘Previous’ pointer points up); an ‘Up’ pointer usually leads to a node at the level above (closer to the ‘Top’ node); and a ‘Menu’ leads to nodes at a level below (closer to ‘leaves’). (A cross reference can point to a node at any level; see Cross References.)
Usually, an @node
command and a chapter structuring command
are conventionally used together, in that order, often followed by
indexing commands. (As shown in the example above, you may follow the
@node
line with a comment line, e.g., to show which pointer is
which if explicit pointers are used.) The Texinfo processors use this
construct to determine the relationships between nodes and sectioning
commands.
Here is the beginning of the chapter in this manual called “Ending a
Texinfo File”. This shows an @node
line followed by an
@chapter
line, and then by indexing lines. The manual uses
implictly determined node pointers; therefore, nothing else is needed
on the @node
line.
@node Ending a File @chapter Ending a Texinfo File @cindex Ending a Texinfo file @cindex Texinfo file ending @cindex File ending
An earlier version of the manual used explicit node pointers. Here is
the beginning of the same chapter for that case. This shows an
@node
line followed by a comment line, an @chapter
line, and then by indexing lines.
@node Ending a File, Structuring, Beginning a File, Top @comment node-name, next, previous, up @chapter Ending a Texinfo File @cindex Ending a Texinfo file …